Skip to Content
  • Optical Boxes/Patch Panels
  • SC-LC-ST Adapters
  • Pigtails
  • Pre-Polished Connectors
  • Glue-On Connectors
  • Bifiber Patch Cords
  • Splice Closures And Accessories
  • Accessories
  • Fiber Optic Termination System
FBC-007 UniCam Connector flat cleaver
UniCam Connector Flat Cleaver FBC-007 for the precision cut of optical fibers
0.0 EGP
Kevlar crimping tool for ST/SC connectors
Kevlar crimping tool for ST/SC connectors
0.0 EGP
Optical fibers cleaver Mini50GB for fusion splicer with fiber waste bin, Auto Pushback machanism
The Mini50GB is a high precision cleaver to be used with fusion splicers for cutting the optical fibers. The cleaver is equipped with an integrated system to place and fix the fibers, a diamond blade which allows 90° cuts with a maximum tolerance of 0,5° and a collector for the surpluses of the cut fibers.
0.0 EGP
FO inspection microscope 200X
FO inspection microscope
0.0 EGP
Fiber fault locator
Compact tool for testing individual optical fibers and for problem solving before and during the termination. By emitting red light it detects fault points in fiber patch cords or in fiber segments close to the connector. Detection range up to 3 Km
0.0 EGP
TKT-UNICAM-PRETIUM Termination kit for pre-polished connectors
Termination kit for pre-polished ST/SC/LC connectors, both multimode and single-mode. The suitable connectors for this system contain a short length of an optical fiber fixed with resin and polished. Once the optical fibers are cleaned, they will be cut with the “Pretium Flat Cleaver”, inserted into the pre-polished connector up to the internal fiber-end and mechanically fixed with the “UniCam Pretium Installation Tool”. Thanks to the CTS integrated system for the splice verification, the immediate test of the performance can be made through two simple leds.
0.0 EGP
FF4S+ Active Clad alignment fusion splicer
Fusion splicer, with adaptive clad alignment type V-Groove for the splicing of single-mode and multimode optical fibers or pigtails. The ends of the two optical fibers to splice, after proper alignment, are spliced by ensuring absolute continuity of the optical wave guide. Splicing is obtained by heating the fibers through an electric arc.
0.0 EGP
Splice wipes 4.4″ x 8.4″, dispenser pack of 280 pcs
One-layer fabric splice swipes to clean optical connectors
0.0 EGP
Polishing discs 2,5 mm for ST/SC optical connectors.
Polishing discs for optical connectors. Available with 2.5 mm ferrule for ST/SC connectors
0.0 EGP
Click cleaner for SC-ST connectors with 2,5 mm ferrule, up to 800 cleaning operations
Click cleaner for SC-ST connectors with 2,5 mm ferrule
0.0 EGP
0.0 EGP
Polishing paper for connectors – 12 µm, 10 pcs pack
Polishing paper 3 µm grade 100×100 mm for FO connectors
0.0 EGP
Polishing paper for connectors – 9 µm, 10 pcs pack
Polishing paper 3 µm grade 100×100 mm for FO connectors
0.0 EGP
Polishing paper for connectors – 3 µm, 10 pcs pack
Polishing paper 3 µm grade 100×100 mm for FO connectors
0.0 EGP
Fiber stripper
Fiber stripper
0.0 EGP
Isopropyl alcohol in spray can 400 ml
Isopropyl alcohol suitable to clean optical fibers before splicing.
0.0 EGP